rpm7200-hx series photo link module 1/6 ir receiver module rpm7200-hx series rpm7200-hx series are remote control receiver module. small-sized, light-weight, and low voltage operated (from 2.7v) modules have been achieved by using resin mold. ! ! ! ! applications all household electric appliances such as tv, dvd, air conditioner and audio equipment. ! ! ! ! features 1) low voltage operation. (v cc =2.7 3.6v) 2) low current consumption. (i cc =0.3ma, v cc =3v) 3) superior anti v cc noise characteristics. 4) 3 types of holders available to each set. ! ! ! ! rpm7200 series center frequency top view side view rsip-a3 (h4) rsip-a3 (h3) rsip-a3 (h5) 15.9mm 19.0mm RPM7237-h3 rpm7238-h3 rpm7240-h3 9.6mm RPM7237-h5 rpm7238-h5 rpm7240-h5 RPM7237-h4 rpm7238-h4 rpm7240-h4 height to lens 36.7khz 37.8khz 40.0khz ! ! ! ! absolute maximum ratings (ta = 25 c) parameter symbol limits unit v cc 6.3 ? 30 + 100 2.0 v c 260 ? output current tstg i o tsol c ma supply voltage storage temperature soldering temperature ? within 5s. ! ! ! ! recommended operating conditions (ta = 25 c) parameter symbol min. typ. max. unit operating voltage operating temperature voltage v cc 3.0 v 2.7 3.6 topr 25 c ? 10 75
rpm7200-hx series photo link module 2/6 ! ! ! ! block diagram amp 100k ? r out gnd v cc i / v bpf comparator limiter detector ! ! ! ! terminal description pin name pin no. function 1v out output terminal ground power supply 2 3 gnd v cc ! ! ! ! electrical characteristics (unless otherwise noted, ta = 25 c v cc =3v) isink=200 a outer light condition ee < 10 (ix) outer light condition ee < 10 (ix) outer light condition ee < 10 (ix) parameter symbol min. typ. max. unit conditions i cc v h l v l t on t off fo 300 a 15 ? ? 600 500 m ? v ? v s 0.5 800 1/2 1/2 600 ? 3 ? 1 ? 1 ? 1 ? 1 ? 1 ? 2 ? 2 ? 8 400 2.5 ? 400 ? ? ? 35 45 s 800 khz ? ? deg deg ? ? 1 600/600 s burst wave is transmitted by standard transmitter. however, it must be measured after the initial transmission pulse is 100 p ulse. ? 2 it is an angle when the linear arrival distance become half. ? 3 three types of frequencies : 36.7, 37.9, 40khz. consumption current no outside light, no signal input effective distance high level output voltage low level output voltage on pulse width off pulse width center frequency vertical half angle horizontal half angle ! ! ! ! measurement conditions (1) transmit signal 600 s 600 s fig.1 transmit signal carrier frequency=fo, duty=50%
rpm7200-hx series photo link module 3/6 (2) standard transmitter fig.2 measurement of standard transmitter proofreading standard transmitter r 20cm io=v out / r peak=940nm ? =40nm rpm-302b v out when standard transmitter output the signal at fig.1 standard photodiode output become io=5 ap-p under the measurement condition fig.2. (the radiant intensity of standard transmitter : 50mw / sr) rpm-302b : standard photodiode has short current isc=27 a at e=1000(lx) (using cie standard light source a) (3) measurement effective distance, horizontal & vertical half angle fig.3 measurement condition for effective distance rpm7200-hx series light detector face illuminance : ee effective distance : l ( ; indicates horizontal and vertical directions) standard transmitter effective distance l : effective distance at =0 fig.3 horizontal & vertical half angle : the angle which effective distance became 50% of l.
rpm7200-hx series photo link module 4/6 (4) output signal 600 s t on t off v cc gnd 1/2 v cc v h v l 600 s fig.4 carrier frequency=f 0 carrier duty=50% transmit signal output signal (5) measurement circuit for the output voltage and the consumption current fig.5 v cc v h , v l v cc i cc r out gnd a v rpm7200-hx ! ! ! ! notes (1) all characteristics of the receiver in this specification are specified by supplying burst wave form with rohm standard transmitter (fig.2 ). if in case of other burst wave form will be used, please check these spec. carefully under the evaluations. (2) when the receiver will be used as the wire-less remote controller, please use the signal method the signal format which refer to ?measures to prevent mulfunctioning of ir remote-controlled electric home appliances?. (published july 1987 by association of electric home appliances) if using other signal method, signal format, (ex: signal format which not including the leader signal) the receiver might have chances to miss-function. (3) please set up transmitter?s carrier frequency as same as the receiver?s f 0 frequency. otherwise error might be occurred.
rpm7200-hx series photo link module 5/6 (4) if transmission signal has non-continues carrier, error might be occurred. continuous carrier is necessary. t1 t2 t1 t2 (5) the receiver was designed to use as in-door use only. therefore, please understand that the receiver cannot cover all characteristics, in case of using it out-door. (6) noise environment (light noise from inverter lamp, and other kind of lamps, power ripple, electromagnetic noise from power circuit, and etc) may cause a reduced effective distance. (7) emitting unit (remote control transmitter) has to be considered about its emitting device function, characteristics and characteristics of the receiver. (8) please connect ?holder? on to the ?ground (gnd)? of pcb. if the holder is not connected to the gnd, there is a possibility of worsening the characteristics of product. (9) do not supply unnecessary stress to lead. (10) please pay careful attention to the lens. it might have a chance to miss-function when the lens get dust or dirty. and also please do not touch the lens. (11) in order to prevent ic from esd, human body and solder iron, etc. are required to be grounded.
rpm7200-hx series photo link module 6/6 ! ! ! ! external dimensions (units : mm) rsip-a3 (h3) rsip-a3 (h4) rsip-a3 (h5) 11.0 1.7 8.8 1.7 1.8 14.0 21.95 2.95 7.0 3.6 3.6 6.1 6.0 0.5 0.4 0.6 0.6 7.3 c3 3.6 2.54 2.54 3.6 1.8 7.3 2.54 2.54 15.9 4.2 2.35 1.4 1.4 0.4 0.6 0.6 0.5 12.65 7.0 2.95 0.65 6.3 1.4 4.6 1.4 2.5 0.4 1.8 9.0 12.55 3.6 2.54 2.54 2.95 1.0 6.0 0.5 0.6 0.6 7.3 3.6 rout pin no. gnd v cc
|
